Top 10 usual forklift accidents ， forklift procedure need to pay attention to these issues ！.

Top 10 usual forklift accidents ， forklift procedure need to pay attention to these issues ！.

Blog Article

Don't underestimate the forklift at work. If the procedure is not good, there will be serious accidents in minutes, and there are numerous crashes including forklifts.

Instance 1: The forklift cargo blocked the vehicle driver's view, and the individual ahead can not be discovered, causing a moving crash.
Situation 2: In order to keep the balance of the forklift when raising heavy goods, the staff members utilized their body weight as the counterweight, which practically created casualties.
Instance 3: The width of the forklift cargo exceeds the allowed width of the route and hangs on the roadside rack, which practically causes an accident.
Instance 4: Forklift is speeding up and surrender throughout a turn.
Situation 5: The forklift vehicle driver did not notice the pedestrian, and the pedestrian did not see the forklift.
Case 6: The forklift raises the employees unlawfully, the forklift chauffeur does not put on the safety belt, the forklift lifter drops and the motorist is squashed when the forklift rolls over.
Case 7: The forklift motorist did not put on a seat belt and dropped from the automobile when it surrendered and was squashed.
Forklift procedure need to take notice of these matters ：.

Start.
1. Prior to starting, observe the environments, and after confirming that there are no challenges that hinder the safety and security of driving, beep the horn first and after that start.
2. For vehicles with hydraulic (air pressure) brakes, the brake hydraulic pressure ( atmospheric pressure) gauge have to be secure prior to starting.
3. When the forklift starts with a load, the vehicle driver must initially verify that the tons is secure and reliable.
4. The start has to be sluggish and stable.

Driving.
1. When driving, the height between the bottom end of the fork and the ground need to be kept at 300mm-400mm, and the pole should be slanted in reverse. .
2. Do not raise the fork too expensive when driving. When going into and leaving the work site or while driving, beware that there will be no obstacles overhead. When the load is traveling, the fork has to not be elevated too expensive, which will influence the security of the forklift. .
3. After dumping, the fork must be reduced to the regular driving position prior to driving. .
4. When turning, if there are pedestrians or vehicles nearby, the driving signal should be released initially. High-speed sharp turns are banned. High-speed doglegs will cause the car to shed lateral stability and topple. .
5. When the forklift is downhill, it is strictly restricted to shut off the flame and slide, and it is restricted to brake unexpectedly while driving with tons unless there are special circumstances.
6. When the forklift is running, it has to comply with the web traffic rules in the factory and need to maintain a specific safety and security distance from the car in front. .
7. When the forklift is running, the load has to be in the lowest setting that does not impede the driving, and the gantry ought to be effectively tilted back. The tons shall not be increased except when stacking or loading. .
8. The height of the load must not block the chauffeur's sight. In unique conditions, when the product influences the forward vision, drive at a reduced rate when reversing.
9. It is prohibited to activate the ramp, nor to drive throughout the ramp. .
10. The secure driving rate of the forklift in the factory location is 5 km/h, and it needs to drive safely at a low rate when going into the manufacturing workshop location. .
11. When the forklift is lifted, raised or driven, it is restricted for employees to base on the fork to hold things and play a stabilizing role. .
12. If troubles are found, they will be repaired and reported in a timely fashion, and they will certainly never run with illnesses or hide them.

packing and unloading.
1. When fork-loading items, the range in between both forks need to be readjusted as required to make the load of the two forks balanced and not skewed, and one side of the thing need to protest the shelf. .
2. It is restricted to deal with a single fork or use a fork top or draw. In unique situations, security indication should be established to remind bordering pedestrians. .
3. In the process of packing and unloading products, the forklift has to be braked with the brake. .
4. The speed of the automobile must be slow and constant. Take care not to roll the wheels on the dunnage, so as not to stretch the rolled things and harm individuals. .
5. When making use of a fork to fork the goods, the fork must be as deep as feasible under the load, and it ought to be noted that the fork idea ought to not touch various other goods or items. The lots must be supported with very little back tilt of the gantry to make sure that the load does not glide backwards. The mast can be slanted forward somewhat when the lots is reduced to allow for very easy placement of the lots and extraction of the forks. .
6. It is forbidden to fork items at high speed and ram tough things with the fork head. .
7. When the forklift is functioning, it is forbidden for people to stand around the fork, so as to prevent the collapse of the goods and injure people. .
8. Overloading is restricted, and it is forbidden to use forks to raise employees to engage in high-altitude procedures to stay clear of high-altitude dropping accidents. .
9. It is not allowed to use the brake inertia to slide, place, round or roll things. .
10. It is not enabled to make use of forks to select, transform pallet unload.

Leaving .
1. It is forbidden to leave the forklift when the items on the fork impend. Prior to leaving the forklift, you must dump the goods or reduced the fork structure.
2. Draw the parking brake manage to dead or depress the parking brake switch.
3. The engine is turned off and the power is removed. (Except for special situations, such as the motorist does not leave the car's line of sight and does not go beyond 1 min).
4. Eliminate the trick. .

Forklift Operation Precautions.
1. Prior to and after the forklift operation, the look must be examined, and gas, lubing oil and cooling water should be added.
2. Examine the safety efficiency of starting, running and stopping.
3. Check whether the lights and horn signals are full and efficient.
4. During the operation of the forklift, check whether the pressure and temperature are typical.
5. After the forklift is running, the exterior leakage should additionally be examined and the seals ought to be replaced in time.

Forklift Safety Operation Specifications.
1. You must examine before leaving the car;.
2. When you encounter somebody before you during driving, you must send out a signal at a distance of 5 m;.
3. The driving rate in the factory does not surpass 5 km/h;.
4. When driving, the low point of the cargo must be 0.3 m ~ 0.4 m above the ground;.
5. The transforming must not be too sharp to avoid the propensity of " complimentary switching";.
6. Adding and down the slope ought to be sluggish and uniform, and no turning on the slope is allowed.
7. Do not drive throughout the gradient. When the slope is above 10%, the car must be driven in reverse when declining;.
8. When the forklift personnel carry the goods and move forward, if they encounter huge or heavy products and go to the chauffeur's line of sight, they need to take the reversing workout
.
The "Eight Prohibitions" ought to be adhered to in the procedure.
1. Solitary fork operation is not permitted.
2. It is not enabled to raise the goods for long distance driving.
3. It is not enabled to pick up the goods by handing over the pallet with the fork.
4. It is not permitted to directly shovel chemicals, flammables and various other hazardous chemicals with forks.
5. It is not permitted to make use of inertia pressure to grab the goods.
6. It is not enabled to make use of braking force to expatriation round or easy-to-roll things.
7. It is not permitted to bring people to service the pallet or fork, and it is purely prohibited to stand under the fork after the fork is elevated.
8. Do not drive laterally on inclines
.
Vehicle parking is not allowed under the list below conditions.
1. Curves, slim roads, train crossings;.
2. Sections with a longitudinal slope Stand-on Electric Pallet Stacker above 5%.
3. When there is an barrier on one side of the roadway, the opposite side of the section with the same size Stand-on Electric Pallet Stacker as the challenge ought to be within 20 meters at each end.

Web：https://www.onenforklifts.com/
Email：[email protected]
Phone：+86 13827083844